No products in the cart.
The Potassium Ion-Selective Electrode is fully supported with LabQuest 2, a standalone data logger with built-in graphing and analysis software.
Learn more about LabQuest 2 »
Product Description
£285.00 ex VAT | £342.00 Inc VAT
The Potassium Ion-Selective Electrode makes the measure of potassium ions portable. When used with a Vernier LabQuest 2, the Potassium ISE can be used to take readings in the field at lakes or streams. This sensor is easier to set up and use than other methods of measuring potassium ion concentration in aqueous solutions. Because it is a stick-style sensor, its use is similar to using a conductivity probe or a pH sensor in a laboratory setting or in the field.
Ion-Selective Electrodes require good chemical technique and careful calibration to obtain accurate results. They are not recommended for middle school or elementary students.
We recommend that you do not purchase Potassium Ion-Selective Electrode replacement modules too far in advance of their expected time of use; degradation occurs while replacement modules are stored on the shelf.
Available to Order
Experiments
Experiments Include:-
Measuring Potassium in Commercial Products
Measuring Potassium in Foods
What's Included
- Vernier Potassium Ion-Selective Electrode
- 30 mL bottle of High Standard Standard (1000 mg/L)
- 30 mL bottle of Low Standard Standard (10 mg/L)
- ISE soaking bottle (empty bottle with insertion cap)
- User manual
Specification
- Range: 90 – 39,000 mg/L (or parts per million)
- pH Range: 2 to 12
- Interfering Ions: Rb2+, Cs2+, NH4+, Ca2+, Mg2+, Li+
- Temperature Range: 0 – 40°C (not compensated)
- Electrode Resistance: >50 mΩ
- Electrode Slope: 56 +/- 4 mV/decade at 25°C
- Calibration Voltage (typical): 2.7 V (1000 ppm), 1.9 V (10 ppm)
- Reproducibility (precision): +/- 11% of full scale
- Minimum sample size: 3 mL in a 50 mL beaker
- Accuracy: +/- 16% of full scale
Sensor Requirements
The Potassium Ion-Selective Electrode may require a compatible interface and software. Choose a platform below to see compatible interface and software options.
| Interface | Software | ||
|---|---|---|---|
| Graphical Analysis 4 for Computers | Logger Pro | Logger Lite | |
| LabQuest Mini | Full support | Full support | Full support |
| LabQuest 2 | Full support | Full support | Full support |
| LabQuest Stream | Full support1 | Full support1 | Full support1 |
| Go!Link | Full support | Full support | Full support |
| Original LabQuest (DISCONTINUED) | Full support | Full support | Full support |
| LabPro (DISCONTINUED) | Incompatible | Full support | Full support |
COMPATIBILITY NOTES
- Connect LabQuest Stream via USB. Future software updates will support connection via Bluetooth®technology
- A computer with a compatible Bluetooth® 4.0 radio is required. Only computers running Windows 10 or Mac OS X 10.10 or newer are supported.
| Interface | Software Graphical Analysis 4 for Chrome |
|---|---|
| LabQuest Mini | Full support |
| LabQuest 2 | Full support |
| LabQuest Stream | Full support1 |
| Go!Link | Full support |
| Original LabQuest (DISCONTINUED) | Full support |
COMPATIBILITY NOTES
- Connect LabQuest Stream via USB. Future software updates will support connection via Bluetooth®technology
| Software | ||
|---|---|---|
| Interface | Graphical Analysis for iOS | Graphical Analysis for Android |
| LabQuest Stream | Future support | Future support |
| LabQuest 2 | Full support1 | Full support1 |
| Go Wireless Link | Future support | Future support |
COMPATIBILITY NOTES
- Mobile devices can only connect to LabQuest 2 via Wireless Data Sharing.
Ideal Solutions for Enquiry Based Learning
5 Year Warranty on most items
Award Winning Products
Connectivity with iOS, Mac, Android, Windows and Chromebooks
Guaranteed Quality and Support
Extensive Support Materials
Related Products
Use the Dissolved Oxygen Probe to determine the concentration of oxygen in aqueous solutions in the field or in the laboratory. The Dissolved Oxygen Probe is great for biology, chemistry, ecology, or integrated science courses. It can be used to perform a wide variety of experiments to determine changes in dissolved oxygen levels, one of the primary indicators of the quality of an aquatic environment. Also see our NEW Optical Dissolved Oxygen Probe
£298.00 ex VAT | £357.60 Inc VAT Add to basket
This sensor is used to measure voltages in the range of -30 to +30 volts
£64.00 ex VAT | £76.80 Inc VAT Add to basket
Use the Drop Counter to perform accurate, automatic titrations. Record the number of drops or calibrate the drop size to record volume of titrant added during a titration. Logger Pro software can automatically convert the number of drops into volume. The Drop Counter can be used for conductimetric or potentiometric titrations using our Conductivity Probe, Ion-Selective Electrodes or any electrode with a 0 to 5 volt output.
£129.00 ex VAT | £154.80 Inc VAT Add to basket
Designed for much higher forces than the Dual-Range Force Sensor, the Force Plate can measure the forces developed during stepping, jumping, and other human-scale actions. For example, you can perform the following kinds of experiments:
£376.00 ex VAT | £451.20 Inc VAT Add to basket- Observe the change in normal force during a ride in a lift.
- Measure the impulse delivered by the floor during a jump.
- Measure the reaction force as a student leans against a wall.
Use the Charge Sensor as an electronic electroscope to obtain quantitative measurements when studying charging by induction, friction, or contact.
£103.00 ex VAT | £123.60 Inc VAT Add to basket
Ideal for most acceleration experiments. Use it for studying the one-dimensional motion of a car (real and toy), lift, pendulum bob, or amusement park ride.
£116.00 ex VAT | £139.20 Inc VAT Add to basket- Range: -50 to +50 m/s2
- Typical accuracy: ±0.1 m/s
Use the Dual-Range Force Sensor in a wide variety of experiments including the study of friction, simple harmonic motion, impact in collisions, or centripetal force. The Dual-Range Force Sensor has two ranges: ±10N or ±50N. It can be easily mounted on a Vernier Dynamics Cart for use with the Vernier Dynamics System. Mount one on the New Centripetal Force Apparatus, on a ring stand or even as a replacement for a hand-held spring scale. Use it to study friction, simple harmonic motion, impact in collisions, or centripetal force.
£142.00 ex VAT | £170.40 Inc VAT Add to basket
The Conductivity Probe determines the ionic content of an aqueous solution by measuring its conductivity. This has many applications in chemistry, biology, and environmental science. The Conductivity Probe has three ranges, providing optimal precision in any given range. Biology teachers can use this probe to demonstrate diffusion of ions through membranes. Chemistry students are able to quickly investigate the difference between ionic and molecular compounds, strong and weak acids, or ionic compounds that yield different ratios of ions. Environmental science students use it to measure TDS, total dissolved solids.
£129.00 ex VAT | £154.80 Inc VAT Add to basket
The Mini GC Plus has been replaced by the Go Direct Mini GC.
The Mini GC Plus is a portable instrument for separating, analyzing, and identifying substances contained in a volatile liquid or gaseous sample. The Mini GC uses Air as its carrier gas so no external gas cylinders required.
Use the High Current Sensor in experiments that involve currents larger than 1 A, such as solar panels, hand generators, and other alternative energy projects. The High Current Sensor has a range of ±10 A. Current is measured with a Hall Effect sensor, which uses the magnetic field created by the current and therefore does not add a resistive element to the circuit. A metal shield over the Hall Effect chip reduces the influence of external magnets. A replaceable fuse protects the equipment and circuit
£103.00 ex VAT | £123.60 Inc VAT Add to basket
The Vernier Optical DO Probe uses luminescent technology to provide fast, easy, and accurate results, making it a terrific choice for biology, ecology, or environmental science courses. Students can measure dissolved oxygen concentration in surface water or to perform a wide variety of experiments to determine changes in dissolved oxygen levels, one of the primary indicators of the quality of an aquatic environment. Using Plug and play technology, no filling solution is required, no warm up time needed, no stirring and no calibration.
£389.00 ex VAT | £466.80 Inc VAT Add to basket
The Vernier Go Wireless Heart Rate is ideal for continuously monitoring heart rate before, during, and after exercise or while a person is stationary. Data are wirelessly transmitted to iPad, LabQuest 2, or other mobile devices that are Bluetooth® Smart Ready. It is simple and easy to use, displays live heart rate readouts before data collection, and is easy to clean and share between students.
£116.00 ex VAT | £139.20 Inc VAT Add to basket
The Anemometer can be used in a variety of experiments to measure wind speed. Can either be used hand held to measure wind speeds, or used with the accessory rod for static experiments such as in front of wind tunnels. The Vernier Anemometer is an impeller-type anemometer that measures wind speed in the range of 0.5 to 30 m/s (1 to 67 mph).
£116.00 ex VAT | £139.20 Inc VAT Add to basket
This is great for studying one-dimensional collisions or any motion with larger accelerations.
£125.00 ex VAT | £150.00 Inc VAT Add to basket- Range: -250 to +250 m/s2
- Typical accuracy: ±1 m/s2